Single-Sided Wall with AluStarTec

AluStarTec wall formwork is a robust multi-purpose system covering large forming areas and heights up to 3.30 m. It has a high load capacity of 60 kN/m² for high, fast pours in industrial and civil engineering. 

Scroll down this page to finde the components that you will need when formwing a wall with AluStarTec. Note that each building project will vary in terms of the number of parts needed. If you need assistance in planning the pour, please consult with us via the contact form. 

You will find additional information on the AluStarTec system on the product page.

Contact Form

 
 
 

References AluStarTec

  • Bridge Building for beltway M 0 in Budapest/Hungary

    A simple, sophisticated design featuring few components and time-saving details distinguishes the MEP Shoring System, which consists of only three parts and, yet, is versatilely applicable: as single prop, slab table or shoring structure.

  • Bjørvika Reshapes Oslo Skyline

    The leading Norwegian concrete contractor BundeBygg AS, chose MEVA for all concrete works, including cores, elevator and staircase shafts, inside and outside walls, columns and slabs.

  • Waterway Crossing, Minden

    MEVA wall formwork Mammut was chosen because of its load capacity of 100 k/N/m².

 

Product List

 
 
Formwork
Ties
Bracing
Safety
 
 
  • ST panels

    Construction height 12 cm, frame profile width 4 cm. Three tie holes per panel height 330 cm, two tie holes per panel height... 

  • ST panel 270/45 with concreting window

    Is used to control the pouring process when control is not possible from above. 

  • ST panel AL 17, 270/45 with filling nozzle

    Is used when concrete cannot be poured from above, e.g. tunnel formwork. Connection with a manual gate valve. Operating... 

  • ST inside corner

    For 90° corners. Side length 25 cm. Steel frame with tie holes and alkus facing or exchangeable steel sheet. 

  • AS/ST outside corner

    Aluminium. Provides together with ST panels and AS assembly locks a fast and stable outside corner assembly for 90° angles. 

  • AS hinged inside corner

    Steel construction with steel sheeting. Side length 30 cm. Adjustable angle 60°-180°. 

  • AS hinged outside corner

    Steel construction with steel sheeting. Side length 7,5 cm. Adjustable angle 60°-180°. 

  • AS assembly lock

    Galvanized. Tightly connects and aligns AluStar and StarTec panels. Clamping length 8 cm.  

  • Uni-assembly lock

    Galvanized. For stepless compensation. Clamping length 22 cm or 28 cm. 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

  • ST aluminium filler

    Aluminium with high-quality annealed powder coating. With tie holes. For length compensation of 5 cm, especially in corners.... 

  • ST compensation plate

    Steel construction with steel sheeting. Is used to compensate gaps of 8 to 20 cm and attached to the panel with 2 assembly... 

  • AS timber profile

    Timber profile with groove. To support job-built fillers of 14 cm or more or to connect job-built formwork with 21 mm... 

  • Cross beam 300

    Coated. Links formwork in vertical position and support frames with flange screws. Allows to build transport units.... 

  • M-Cross stiffener 44

    Galvanized. In connection with support frames STB 300 it is used as a tie-beam to transfer the load from the support frame... 

  • AS crane hook

    Is used to move panels. Self-locking. Load capacity: 15 kN (1,5 tons). Always 2 crane hooks required per gang. For use and... 

  • Transport angle 12

    Is used to stack and transport 5 to 12 frame formwork panels with a construction height of 12 cm and 12 cm hole distance.... 

  • MevaTrenn pro

    Not shown. Suited for absorbent and non-absorbent forming faces.Solvent-based. Evaporates when applied, leaving avery thin... 

  • Sprayer

    Not shown. To allow for an even and sparing spraying of the forming surface, suited for (5 litre) MevaTrenn and wax. 

  • Concrete scraper

    With 6 or 10 replaceable hard-metal plates and steel ledge. Wooden stick (ash-tree) with handle. 

  • Beam clamp H20/H20

    Galvanized. Is used to attach planks or cross beams to H20 beams when using slab tables. 

  • Safety bolt

    Secures stacked panels. 

  • Plug D20

    Is used to close unused tie holes (AluFix, EcoAs, AluFix, AluStar and StarTec). 

 
 
  • Flange screw 12

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

  • Brace bracket 80

    Galvanized. Can be used for floor slabs and slab ends up to 80 cm high. Can be inclined by up to +/- 15°. With plastic nail... 

  • Double-headed ground nail 25/280

    Not shown. Is used to attach brace bracket 80. Double-headed. Is removed from the earth with the extractor. (to be ordered... 

  • Anchor support DW 15 - DW 26,5

    Steel, uncoated. Bottom bent by 45°. Supports DW 15, DW 20 and DW 26,5 tie rods.The tie rods are re-usable if PVC sleeves... 

  • Double anchor DW

    Steel, uncoated. Admissible load: DW 15 = 180 kN, DW 20 = 320 kN. Is used for 45° anchoring in the bottom slab when using... 

  • Coupling nut

    With DW thread. DIN 18216. Connects tie rods to the anchor loops when length extension is necessary. Adm. load capacity and... 

  • Upstand bracket

    Adjustment range 100 mm. Is used to brace upstand formwork. 

  • Tie rod DW

    Uncoated; not weldable; with DW thread; DIN 18216. To transfer the load from the support frame into the floor slab or... 

  • Fix anchor

    Uncoated. Is used to anchor tie rods in the concrete with anchor supports. 

  • Pressure gauge

    Not shown. Measures tractive force of anchors from 250 to 400 kN. Includes compensating plate for tie rods, with 50 mm hole... 

 
 
  • Walkway bracket

    Galvanized, yellow, pluggable. Is used as working and safety scaffold. Is attached to the multi-function profile and secured... 

  • Support frame STB 300

    Sturdy steel construction, coated: Height 2,20 or 3,00 m. Is used to brace single-sided wall formwork up to a pouring... 

  • Support frame STB 450

    Sturdy steel construction, coated, height 4,50 m. To brace single-sided wall formwork up to a pouring height of 5,00 m. A... 

  • Height extension connector STB 450

    Not shown. Coated. Connects the support frame STB 450 with the STB-height extension 150 and the height extensions to each... 

  • STB-height extension 150

    Coated. Height 1,50 m. Extends support frame STB 450 by 1,50 m (one or several times). Pouring heights of 7,50 m (or higher)... 

  • STB-base extension

    Coated. Is used for the one-time or -multiple backward extension of support frame STB 450 and for the attachment of Triplex... 

  • Base extension 300/200

    Coated. Supplements the support frame STB 300 for special applications, which require a detailed planning and static... 

  • Support frame STB 450 for mobile unit

    Not shown. The support frame STB 450 for mobile unit is equipped with an additional steel plate so it can be distinguished... 

  • Cross beam 300

    Coated. Links formwork in vertical position and support frames with flange screws. Allows to build transport units.... 

  • M-Cross stiffener 44

    Galvanized. In connection with support frames STB 300 it is used as a tie-beam to transfer the load from the support frame... 

  • Push-pull prop R

    Galvanized. Garantee tensile and compression strength. Align and brace wall formwork. Foot plates and... 

  • Braces SRL

    Galvanized. Guarantee tensile and compression strength. With right-hand and left-hand spindle and revolving centre part.... 

  • Ladder

    Galvanized. Is hooked into the CF-access platform and automatically secured. Can be extended with extension ladders. Safety... 

  • Head bolt 16/90

    Galvanized. Is used to attach push-pull props or braces to foot plates and formwork-prop connectors. 

  • Cotter pin 4

    Not shown. Galvanized. Locks the head bolt. 

  • Scaffold tube

    Galvanized. Is used to reinforce large-size units of support frames or climbing systems for transport.  

  • Rigid coupler 48/48

    Galvanized. Connects 2 scaffold tubes with Ø 48,3 mm at an angle of 90°. SW 22. 

  • Swivel-joint coupler 48/48

    Galvanized. Connect 2 scaffold tubes with Ø 48,3 mm at any angle required. 

  • Bolt-on coupler 48/M14

    Galvanized. Permits the attachment of scaffold tubes with Ø 48,3 mm to support frames, climbing brackets, etc. 

  • Joint coupler 48/48 SW 22

    Galvanized. Is used together with a tube connector 48 to attach scaffold tubes with Ø 48,3 mm at tube joints. 

  • Tube connector 48

    Galvanized. Is required for joint coupler 48/48 and used to reinforce the joint of 2 tubes. 

  • Triplex SB

    Galvanized. Provides together with the base extension the required additional support for concreting heights of 7,50 m (or... 

  • Fixing screw 35/DW15

    Galvanized. Is used to attach a support frame to the tie holes of panels in horizontal position. A flange nut 100 or an... 

  • Stop end bracket SB 110

    Coated. Is used to form stop ends when the pouring height exceeds 4,00 m. For max. wall thickness 1,10 m. A clamping device... 

  • Clamping device for stop end bracket SB 110

    Coated. Is used to connect the stop end bracket SB 110 to the support frame. A flange nut 100 or an articulated flange nut... 

  • M alignment rail

    Galvanized. Are used to brace panel joints for crane ganging, bridge problem areas, brace compensation areas and build stop... 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories to the multi-function profiles of the panels, e.g. alignment... 

  • Cross brace STB

    Coated. Supports the inside corner area of single-sided wall formwork. Dimensions 137 x 137 cm. Welded-in DW-threaded nuts... 

  • Swivel-joint coupler 48/48

    Galvanized. Connects 2 scaffold tubes with 48,3 mm Ø at any angle.  

  • Guard-railing post

    Galvanized. Is plugged into the walkway bracket. 

  • Universal joint connector 76/135

    Galvanized. With head bolt 16/90 and cotter pin 4. Is used to attach push-pull props to vertical or horizontal panel joints... 

  • Formwork-prop connector

    Galvanized. Is used to connect braces, brace frames and push-pull props (max. Ø 48,3 mm) to the multi-function profile with... 

  • Cotter pin 4

    Galvanized. Locks the head bolt. 

Worker protection is mandatory by law from a working height of 2 m. The working platform must be equippped with fall protection on all four sides.

MEVA safety systems offer you a flexible answer to safety requirements, compiled individiually to meet your project needs. Refer to the safety systems page and consult with us on the most effective and cost-efficient solution. 

  • Guard-railing post

    Galvanized. Is plugged into the walkway bracket. 

  • Guard-railing post 48

    Galvanized. With manifold to attach it to the walkway bracket, designed with tube Ø 48 mm to attach tube couplers. 

  • Spiral anchor DW 15/100

    Steel spiral bead, 10 cm long, with styropore core. Is used to attach formwork equipment with tie rods DW 15, e.g. when... 

  • Plastic tube

    Is used as a plastic sleeve for a tie rod that is to be recovered and re-used. 2 m long.  

  • Planing cap DW

    Hard foam, 10 cm long, 45° end piece. For DW 15 and DW 20. Is plugged onto the DW tie rod or on a plastic sleeve for... 

  • Spiral anchor DW 15/100

    Steel spiral bead, 10 cm long, with styropore core. Is used to attach formwork equipment with tie rods DW 15, e.g. when... 

  • Safety cage

    Galvanized. Internal Ø 70 cm. Protects workers when ascending and descending the ladder. The safety cages are attached to... 

  • Anchor support DW 15 - DW 26,5

    Steel, uncoated. Bottom bent by 45°. Supports DW 15, DW 20 and DW 26,5 tie rods.The tie rods are re-usable if PVC sleeves... 

  • Hexagonal nut

    Forged; with DW thread; DIN 18216. To tie the anchors in the bottom slab and at the support frame; is used with a counter... 

  • Single anchor DW

    Steel, uncoated. Admissible load: DW 15 = 90 kN, DW 20 = 160 kN, DW 26 = 250 kN. Is used for 45° anchoring in the bottom... 

  • Access hatch KLK

    Galvanized steel frame. Hatch made from checker plate. Cataphoretic coating; max. opening 88°, self-closing. 

  • Double anchor DW

    Steel, uncoated. Admissible load: DW 15 = 180 kN, DW 20 = 320 kN. Is used for 45° anchoring in the bottom slab when using... 

  • Adjustable spanner

    Not shown. For DW 15, DW 20 and DW 26,5. Is used to loosen and unscrew recoverable tie rods. 

  • Upstand bracket

    Adjustment range 100 mm. Is used to brace upstand formwork. 

  • Articulated flange nut

    Forged, galvanized. DIN 18216. DW thread Ø 15 mm (20 mm). Plate Ø 120 mm (140 mm), max. inclination 10°, SW 27 (36). Max.... 

  • Flange nut 100

    Forged; galvanized. DIN 18216. DW thread Ø 15 mm, plate Ø 100 mm, SW 27. Max. load capacity 90 kN. 

  • Spanner SW 36

    Inset yellow chromated; spanner width 36 mm. To tighten and loosen articulated flange nuts 20/140. 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc....