Wall with EcoAs

The sturdy, hand-set system EcoAs is your flexible, moudlar choice whenever there is no crane time available - ideal for foundations, shafts, swimming pools and small walls. Using a foundation tape, it is possible to tie the EcoAs below and over the top to avoid tie-holes.

Scroll down this page to find a product list showing the parts you may need, when forming a wall with EcoAs. Please note that the number of parts may vary according to the exact specifications. Contact us for advice, consultation, planning and support.  Find out more on our modular hand-set system EcoAs on the product page.  

Contact Form

 
 
 

References EcoAs

 

Product List

 
 
Formwork
Ties
Bracing
Safety
 
 
  • EA panels

    Frame profile height 10 cm, frame profile width 23 mm. Three tie holes per panel heights 300 cm and 240 cm, two tie holes... 

  • EA steel filler

    Completely made of steel, primed and cavity-sealed, with tie holes. For length adjustment of 5 cm, particularly in corners.... 

  • EA compensation plate

    Steel construction with steel sheeting, primed and cavity-sealed. Is used to compensate gaps of 6 to 20 cm and attached to... 

  • EA inside corner Alu(minium)

    Aluminium frame with high-quality annealed plastic coating. All-plastic facing. Aluminium frame with tie holes. For 90°... 

  • EA outside corner

    Aluminium with high-quality annealed plastic coating. Facing 5 cm wide on both sides, integrated chamfer strip. Provides... 

  • EA hinged inside corner

    Steel construction with steel sheeting, primed and cavity-sealed. Side length 30 cm. Adjustable angle 60° to 180°. 

  • EA hinged outside corner

    Steel construction with steel sheeting, primed and cavity-sealed. Side length 7,5 cm. Adjustable angle 60° to 180°. 

  • Assembly lock

    Galvanized. Tightly connects and aligns AluFix and EcoAs panels. Clamping length 4,6 cm. Three assembly locks are required... 

  • Uni-assembly lock

    Galvanized. For stepless compensation. Clamping length 22 cm or 28 cm. 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

  • Dismantling auxiliary 120

    10 cm wide, 120 cm high. Diagonally divided timber filler. Permits easy stripping in restricted areas such as shafts and... 

  • AS alignment rail

    Galvanized. Is used to brace panel joints for crane ganging, bridge problem areas, brace compensation areas and build stop... 

  • Corner bracket 40/60

    Galvanized. Side lengths 40 cm and 60 cm. For inside and outside corners and column formwork. 

  • Crane hooks

    Coated. Is used to move and crane-gang AluFix and EcoAs panels. Self-locking. Load capacity 6 kN (600 kg). Always two crane... 

  • Transport angle

    Is used to stack and transport 5 to 12 EcoAs or AluFix panels. Distance between holes 10 cm. We recommend using 2 foldable... 

  • AS/ST safety bolt, black

    Plastic, black. Secures stacked AluFix, Ecos, AluStar and StarTec panels. 

 
 
  • Articulated flange nut 15/120

    Forged, galvanized. DIN 18216. DW thread Ø 15 mm, plate Ø 120 mm, max. inclination 10°, SW 27. Max. load capacity 90 kN.... 

  • Flange nut 100

    Forged, galvanized. DIN 18216. DW thread Ø 15 mm, plate Ø 100 mm, SW 27. Admissible load 90 kN. 

  • Spanner SW 27

    Inset yellow chromated. Spanner width (SW) 27 mm. Is used to tighten and loosen flange nuts 100, articulated flange nuts... 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

  • Drive nut 60

    Galvanized. DW thread Ø 15 mm, plate Ø 60 mm. Adm. load capacity 90 kN (DIN 18216). Is used to tie the formwork to the... 

  • Tie rod DW 15/90

    Uncoated, not weldable. DW thread Ø 15 mm. Adm. load capacity 90 kN (DIN 18216). Is used to tie panels of a double-sided... 

  • Tie claw 23

    Galvanized. Permits tieing (with tie rod DW 15 and flange nut 100) directly above or beside EcoAs and AluFix panels. 

  • Pressure gauge

    Not shown. Measures tractive force of anchors from 250 to 400 kN. Includes compensating plate for tie rods, with 50 mm hole... 

  • Foundation tape

    Galvanized. Hole spacing 50 mm, hole Ø 16 mm, length 50 m. Adm. tractive force 10 kN. To be cut at hole center. Serves... 

  • Trolley for foundation tape

    Not shown. Is used to transport and cut foundation tapes to length. Suitable for one roll Pneumatic wheels. 

  • Tensioner EA for foundation tape

    Galvanized. Connects the foundation tape to EcoAs or AluFix-panels and serves as bottom tie when panels are assembled in... 

  • Plug D20

    Is used to close unused tie holes (AluFix, EcoAs, AluStar and StarTec). 

  • Stop end bracket

    Galvanized. Is used to form stop ends and suited for frame formwork panels with a profile width of 23 mm (EcoAs, AluFix), 40... 

  • Cone for plastic tube

    Available with 10 mm or 30 mm covering . 

  • Plug

    Is used to close tie holes in the wall when plastic tubes D22 or D30 are applied. Two plugs are required per tie hole.  

  • Water stop

    Uncoated. Lost part for tie rods DW 15 and DW 20 to produce watertight tie holes. Adm. load capacity depends on diameter: Ø... 

  • Stop end fixture 23/40 yellow

    Yellow chromated. Is used to attach alignment rails to the panels when forming stop ends are formed. Or is used in... 

  • Extractor for double-headed ground nail

    Not shown. Is used to remove the ground nail from the earth together with a lever rod (not supplied).  

 
 
  • Ladder

    Galvanized. Is hooked into the CF-access platform and automatically secured. Can be extended with extension ladders. Safety... 

  • Push-pull prop R

    Galvanized. Garantee tensile and compression strength. Align and brace wall formwork. Foot plates and... 

  • Braces SRL

    Galvanized. Guarantee tensile and compression strength. With right-hand and left-hand spindle and revolving centre part.... 

  • Brace frame 250

    Galvanized. Aligns and braces the formwork. Available with or without formwork-prop connector. Consists of a push-pull prop... 

  • Formwork-prop connector

    Galvanized. Connects braces, brace frames and push-pull props (max. Ø 48 mm) to the multi-function profile (with a flange... 

  • Combi-lock with coupling

    Galvanized. Is used to attach push-pull props at the panel joints of AluStar, StarTec, Mammut and Mammut 350 wall formwork.... 

  • Universal joint connector 76/135

    Galvanized. With head bolt 16/90 and cotter pin 4. Is used to attach push-pull props to vertical or horizontal panel joints... 

  • Articulated foot plate

    Galvanized. With head bolt 16/90 and cotter pin 4. For push-pull props and braces of up to Ø 57 mm. 

  • Double-jointed foot plate

    Galvanized. With head bolt 16/90 and cotter pin 4. Serves as foot plate for brace frames 250 and as connector for braces and... 

  • Formwork-prop connector

    Galvanized. Is used to connect braces, brace frames and push-pull props (max. Ø 48,3 mm) to the multi-function profile with... 

  • Cotter pin 4

    Galvanized. Locks the head bolt. 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

Worker protection is mandatory by law from a working height of 2 m. The working platform must be equippped with fall protection on all four sides.

MEVA safety systems offer you a flexible answer to safety requirements, compiled individiually to meet your project needs. Refer to the safety systems page and consult with us on the most effective and cost-efficient solution. 

  • Walkway bracket

    Galvanized, yellow, pluggable. Is used as a working and safety scaffold. Is attached to the multi-function profile and... 

  • Guard-railing post

    Galvanized. Is plugged into the walkway bracket. 

  • Guard-railing post 48

    Galvanized. With manifold to be plugged into the walkway bracket and with 48 mm Ø tube to attach scaffold couplers.  

  • Support guard 800-railing post

    Galvanized. For the side protection at all MEVA wall formwork systems. Allows the extension for guard-railing KLK 230 and... 

  • Swivel-joint coupler 48/48

    Galvanized. Connects two scaffold tubes with Ø 48,3 mm at any angle. 

  • Plastic tube

    Is used as a plastic sleeve for a tie rod that is to be recovered and re-used. 2 m long.  

  • Planing cap DW

    Hard foam, 10 cm long, 45° end piece. For DW 15 and DW 20. Is plugged onto the DW tie rod or on a plastic sleeve for... 

  • Spiral anchor DW 15/100

    Steel spiral bead, 10 cm long, with styropore core. Is used to attach formwork equipment with tie rods DW 15, e.g. when... 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc....