Brake test and development centre for Knorr-Bremse in Munich

Project: Knorr-Bremse, Brake Test and Development Centre, Munich

Contractor: Baresel GmbH, NL München

MEVA Systems: Wall formwork Mammut 350, Column formwork CaroFalt, Shoring tower MEP, MD and ME props, Foldable working platform KAB, Slab formwork MevaFlex

Formwork Engineering: MEVA Formwork Systems, Munich branch, Germany



Industrial Construction at Top Safety Level

Brake test and development centre for Knorr-Bremse

100 different test systems for utility vehicles and freight trains up to 1,585 m long, simulating and testing their braking behaviour according to European and Russsian standards in climatic conditions ranging from -60° C to +80° C. Plus a building area covering 16,900 m², of which alone the experimental workshops take up over 1,000 m².

These are only some of the highlights surrounding the test and development centre being built for Munich-based braking technology corporation Knorr Bremse at its company headquarters. Top international standards regarding safety, process organisation, efficiency, logistics and quality, energy saving and sustainable development are being put into practice.

The challenges facing the concrete team are unusual. Foundations and walls, 40 % of them with a fair-faced concrete finish, columns and slabs were poured using MEVA rental formwork supplied to the contractor Baresel GmbH.

Architecural finish with even tie hole and joint pattern required
The walls, up to 40 cm thick, are up to 15 m high in the basement, 9 m high on the ground floor and 3.80 m high on the upper floors. They were poured using the Mammut 350 wall system. The large wall sections are poured in cycles of 12 m in length. The 3 m panels are ganged to achieve the respective wall heights. Combining same size panels achieves a harmonious tie-hole and joint pattern.

The Mammut 350 system‘s high load capacity of 100 kN/m² saves much time, since there are no limitations on the pour rate up to a height of 4 m. The inside walls, partly interrupted by consoles, intermediary slabs und wall sockets were formed without any site- built shuttering thanks to the system‘s large choice of panel sizes. This, too, contributed to the top concrete finish.

Maximum worker safety thanks to continuous fall protection
Work protection is exemplary. Fall protection is installed without a gap. Even so, safety installations are placed so that work and material flow are not hampered. In addition to the KAB working platforms and MEP shoring towers, safety systems such as the CaroFalt column formwork are in use.

Brake test and development centre A fixed ladder access with safety cage and a working platform with all-round protection are part of the system. No further safety equipment is required.

Site managers Johann Rottenkolber, Andreas Stumpf and Nils Köster come to the following conclusion after their good experience with MEVA formwork and engineering on this challenging construction site:
“The large selection of panel sizes in the Mammut 350 system, the superior concrete finish achieved with every pour and the repair set with which we were able to fix damages to the alkus all-plastic facing on site appealed to the entire construction team.”

  • MEVA Expertise & References

    MEVA Expertise & References

    Referencen for Projets in Commercial & Residential Construction, Architectural Construction, High-Rise Construction and Civil Engineering Construction

  • South Canal Bridge, Ontario: With no crane possible at busy Hwy 400, MevaLite handles the job with ease

    South Canal Bridge, Ontario: With no crane possible at busy Hwy 400, MevaLite handles the job with ease

    One of Ontario’s busiest transportation corridors, Highway 400, began a major expansion project through Kings Township in late 2016. This $79.3 million dollar (CAD) project includes the widening of the highway from three to six lanes in each direction for a two mile stretch and also entails safer on and off ramps, the expansion and realignment of culverts, and the replacement of two bridges − one of them the South Canal Bridge.

  • A Brand-New Theater for the Cincinnati Shakespeare Company

    A Brand-New Theater for the Cincinnati Shakespeare Company

    The new theater is called The Otto M. Budig Theater and located in Cincinnati’s Over-The-Rhine district. When completed, it will become the last section of the planned “Classical Arts Corridor” in Cincinnati, which also includes a Music Hall, School for Creative and Performing Arts, and a park.

  • Budapest: Playing in the shape sorting box

    Budapest: Playing in the shape sorting box

    Children enjoy playing with it, teachers recommend it: the shape sorting box. Based on the popular toy, the architects who conceived the new Meséskert nursery designed the play areas on the top floor as a triangle, circle, and square.

All Plastic Facing alkus
MEVA Frame Profile
... more than just formwork
  •  Select language

    Select continent and country. Language selection optional.

  •  Contact
  •  Search

    Search on our website.

  •  Newsletter

    Subscribe to our monthly newsletter.